3 Reasons to Use an FRL

FRLs – Filters, Regulators and Lubricators – guarantee the efficiency and durability of pneumatic tools. Including an FRL in your air system is vital to running an efficient air line set-up and key to achieving a good return on investment. Adding an FRL in close proximity to the power tool will ensure the required airflow pressure, as well as good air quality by reducing the risk of moisture and dust in the air line. The FRL also helps maintain your air line by providing lubrication.

How to achieve ultimate pneumatic tool performance by optimizing air line installation



An FRL system combines 3 main functions in one system: filtration, regulation and lubrication.

1. Air filtration: The filter cleans compressed air and traps solid particles (dust, dirt, rust).

Dust in an engine could block the air flow and reduce the power of the tool leading to increased maintenance costs as well as high air consumption. Any dirt and rust could also damage the engine resulting in power loss and early wear. This increases tool repair costs and the risk of incident during production.

2. Air regulation: The regulator ensures the consistency of the dynamic working pressure at 90 psi/6.3 bar.

This is important because if the pressure is lower than the one recommended by the manufacturer, the tool can’t reach its performance level and the profitability is decreasing. If the pressure is too high, the tool wears out early. It could also breakdown leading to operator injury and a risk of damage to the application.

3. Air lubrication: The lubricator adds controlled quantities of oil into a compressed air system.

Without lubrication a tool wears out and will stop reaching its maximum level of performance. This in turn leads to a loss of productivity and increased maintenance costs. The graphics below illustrate the durability and the service life of the tool’s air motor with and without lubrication maintenance:

Achieve optimum performance of your tool’s air motor with good lubrication:




Estimated figures based on laboratory tests carried out on pneumatic motors.
(1) Tool’s motor power output
(2) Oil quantity
(3) Tool manufacturer recommendations (available in operator/product manual)


Achieve optimum service life of your tool’s air motor with good air lubrication:


Estimated figures based on laboratory tests carried out on pneumatic motors. 
(1) Tool’s motor power output 
(2) Oil quantity 
(3) Tool manufacturer recommendations (available in operator/product manual)


4 things to consider to select the appropriate FRL unit

There are many different types of FRLs, and so when specifying an FRL there are 4 key considerations:

  1. Environment 
  2. Type of FRL 
  3. Thread size
  4. Tool’s air flow requirements

Important: Make sure you always check manufacturer recommendations.


How to install FRLs



Most pneumatic tool users do not achieve the best performance from their tools because of the air line setup.

To maximize the benefits of using FRLs there are 4 rules to bear in mind:

  1. Always use one FRL unit per tool to ensure the best performance. If more than one tool in use is connected to the same FRL unit, the air pressure and lubrication will be diluted between the different air tools, and you will not benefit from the regulator function.
  2. Mount the FRL units as close as possible to the tool – where the tool hose is connected to the system – to ensure that the oil reaches the tool and to avoid losing pressure.
  3. Always make sure that the lubricator is topped up with oil before using the tool since lubrication maximizes the life of your tool. Read more about oil quantity in our Technical guide “Is your air tool installation right?”
  4. Make sure you maintain the inlet filters regularly: they should be free from moisture and dirt.


Safety Tips

Pneumatic tools are designed and specified to work at 90 PSI (6.3 bar) dynamic air pressure and with lubrication (find all information in the tools’ operator manuals available in the Chicago Pneumatic website). A higher pressure could affect the tools lifespan, and operator safety (excessive vibration, or abrasive over-speed and burst risk). We recommend using a gauge equipped FRL with every tool to adjust pressure.



Links

Air Filters

Air Accessories - Filters, Regulators & Lubricators in our Online Shop



Who we are and how we can help!

Ash Air has been around in New Zealand since 1979, and we’ve grown into a nationwide company with international support and a reputation for quality and reliability.

We look after all things compressed air for your business!

Ash Air's range of Chicago Pneumatic, Alup, Pneumatech, and Quincy compressors are used extensively around the world in industries ranging from oil and gas to food, automotive and farming, and we bring you these world class compressors here in the land of the long white cloud.

Our technicians are compressed air equipment experts and are dedicated to addressing customer needs. Supported by a 13 locations nationwide, Ash Air offers one of the widest selections of compressed air equipment and parts available today in New Zealand.

Reliability and Efficiency

With Ash Air compressors, you can count on reliability and high performance for even the most demanding applications. We focus our efforts on the following:

Extensive Product Line

We offer a broad array of products, from world class compressor brands, including a full range of rotary and reciprocating air compressors from ½ to 200 horsepower. We serve the compressed air needs of many industries such as the following:

Solutions

In our effort to prioritise the needs of our customers, we work hard to provide solutions. We continually introduce innovative products here at Ash Air to our Kiwi customers, so our end users can rely on us to meet evolving compressed air needs.

Support

We offer an extensive array of air compressor parts and services through our direct locations throughout New Zealand. Continued growth means our operations continue to operate on a national level.

In our effort to provide the best possible support, we offer the following remote monitoring, preventative maintenance, vacuum pump services and overhaul, compressor and pipework installations, hire fleet and leasing solutions, leak detection's and energy audits, and breakdown recovery and emergency air.

When considering new energy-efficient air compressors or an upgrade to more energy-efficient machinery, Ash Air can help you make the right choices for your business.


Read more from #expert corner!


Air compressor leaks can be a substantial source of wasted energy in any system, sometimes wasting 20-30% of a compressor's production. Worst of all, a poorly maintained compressor can have a leak rate expected to equal 20% of total compressed air... …


Choosing the right compressor is essential to your long-term satisfaction and maybe, to the profitability of your business. Many times compressors are based on a single factor alone, such as horsepower or tank size, which is only part of the story. …


In oil injected screw compressors, there is a thin layer of oil found between the rotors to create a seal and maintain proper efficiency as the compression occurs. The unfortunate side effect of this solution is that oil may carry over to the point of use in your air system. This can be mitigated by having correct filtration in place to remove the oil contaminants in your air. Additionally, many individuals may decide to opt for a completely oil-free solution, with the use of a scroll compressor or water injected screw compressor. …


Most businesses concentrate on the air compressor and consider the piping as a secondary concern. The piping system can make or break your business. Faulty, inefficient piping can cause pressure loss and lost power. Keeping a close eye on the overall layout, installations and maintenance of your air piping system will help keep your business running at its’ optimal efficiency. …


Our #1 Focus is Customer Service! Whether you have questions about which compressor is right for you, or if you’re ready to improve your operations and start saving on expenses. Ash Air has been around for over 40 years because we offer reliable and hardworking air compressors, vacuum pumps, and services as well as expert advice and support. …


An oil analysis can prevent problems later down the road. It's often been referred to as the blood test for your compressor. Just like a blood test can tell you about your health and early alerts to impending problems, an analysis can do the same for your compressor. …




Did you know that pressure drops and leaks are the two largest areas of energy loss on your air compressors? It’s easy to understand why a leaking pipe or fitting creates energy loss. Pressure drops are not quite as noticeable, since you cannot hear ... …


Whenever anything doesn't work properly, it's frustrating and we get it. If this is your first time experiencing troubles with your dryer, you're probably unsure where to even start. Getting your dryer repaired and back up and working is critical to ... …


Screw compressors are helpful for an enormous range of applications such as air filling, packaging, tools, HVAC control, and more! One possible drawback is the amount of electricity they use; air compressors can be a huge drain on energy if used ​ine... …



Most air compressors require constant oil lubrication to prevent friction on the pistons or screws and other moving parts. To make sure your air compressor is running efficiently, it is important to check your oil level regularly and to know how much... …


Have you heard of the term "Total Air Solutions"? A total air solution means everything that goes with the compressor for your business’s air system. 90% of companies require more than just an air compressor.  …


When speaking of air compressors, compressed air treatment is a process that dehumidifies and cleans air before entering the compressor. Most commonly, this process involves air filters and an air dryer. …


Air compressors are used in many different applications and provide essential compressed air to many businesses and individuals with different air needs. No matter what your CFM, PSI and HP requirements are, the electronic controller on your air compressor is the motherboard for keeping your unit running as efficiently as possible. It is your eyes into your machine. …


Air compressors are helpful for an enormous range of applications such as air filling, packaging, tools, HVAC control, and more! One possible drawback is the amount of electricity they use; air compressors can be a huge drain on energy if used ​inefficiently​. If you are running them too long, allowing leaks to exist, or using the wrong type of compressor, you are wasting ​energy and money​. This article will go over some of the biggest power-wasters and how to
stop/prevent them! …



In the following guide, we want to try to answer some of the questions you may have been asking yourself in regards to screw air compressors. If you do not find the answer you are looking for, please get in touch with us. …


Compressed air is a key utility supporting the food packaging and food processing industries. It is used in machines that fill products such as cakes, pies, and liquid products, as well as during the packaging and transportation of snacks, vegetables, beer, soda and other items.. Compressed air must be moisture and contaminant-free to ensure the protection of the food products processed in each facility.  …


Minimizing the risk of accidents in the workplace is a top priority in industry, and it is especially important when working with pneumatic power tools. Ensuring that all safety precautions have been taken to protect the health and wellbeing of operators is vital. With this in mind, here are seven simple steps to reduce the risk of accidents and improve operator safety …


Regardless of the type of compressor you have, vibration issues can be troubling for any business. The root of the vibration can stem from multiple sources, some internally and others externally. Understanding the cause of the vibration and how to resolve them will be critical in keeping your compressor in proper working order. …


Air compressors are essential to your business, but they can also become a safety hazard when used improperly. Reading your owner’s manual and following all proper safety precautions before use is vital in keeping your compressor in great, working condition. …


Corrosion in the pipeline is due to insufficient condensation drainage that occurs during compression. The resulting condensate, together with the compressed air, flow further into the compressed air line network and has a negative effect on the pipes. Find out more about how you can prevent corrosion here. …


FRLs – Filters, Regulators and Lubricators – guarantee the efficiency and durability of pneumatic tools. Including an FRL in your air system is vital to running an efficient air line set-up and key to achieving a good return on investment. Read more here! …


Check out this blog and video included to help you know what you should be looking for when you're thinking about purchasing a Chicago Pneumatic Rotary Screw Compressor for your shop or application. If you want to learn about what a screw compressor actually is, check out this article   …


There are 3 simple steps to make sure your air line installation is providing the right pressure and that your accessories selection is correct, so you can ultimately work productively. It does not take long and it is something you can easily do yourself using our self-diagnostic checklist.  …


Okay, okay, we're a bit excited. With the recent launch of our air tools in our online shop. Here's a 101 for you about what air tools you might need in your air compressor tool kit. Air tools are prevalent in automotive industries, woodworking, construction, metalwork and more. Did you know that there's pretty much an air-powered version nearly any power tool on the market? We want to share with you our 'Must have Air Tools'. …


When you are thinking about an air compressor, you might be have the image of the super popular piston or reciprocating compressor in your mind. The compressor that you see in home workshops, automotive garages pumping up tyres and assisting in spray painting cars. …


As a follow on to our Why You Should Not Use PVC Piping for Your Compressed Air System blog, we share with you what piping you shouldbe using to get the most out of your compressed air system. Here at Ash Air we have the perfect solution if you're wanting to match your great compressor with a fast, easy and reliable piping solution that supports the operational excellence of your whole compressed air system.  …


An air compressor is a big purchase for any business. It is visibly important to properly maintain the air compressor and filter elements to protect that investment. Air intake filters are installed in an air compressor to remove any dust or debris the compress may suck in. Dust will cause wear to the compressor element, valves, filters, compressor oil and any moving parts. …


So you have a vacuum pump installed and you rely on it for your business operations and performance? Here are some reasons why you should consider overhauling your vacuum pump! s with all machinery and compressed air equipment, regular maintenance can help ensure optimised safer performance of your vacuum pump. Learn more about benefits of restoring, rebuilding and repairing your vacuum pump. …


Air compressors are used every day, by many industries around the world. They are often considered the heart of a business, in that most companies will rely on their performance and efficiency to run their operations, to get work done effectively and safely. In your day to day, you've probably seen air compressors in use - whether at a build site powering construction equipment or in a mechanics workshop inflating tyres. …


A scroll air compressor, or spiral compressor, compresses air by drawing it it, trapping it, reducing the volume and discharging it at the outlet port. The scroll compressor that you see today, such as SpiralAIR, have been the result of modernised advancements in manufacturing technology, even thought the concept of a scroll compressor has been around for over 100 years.The scroll compressor is oil-free orbiting, or positive displacement compressor. The compressor has a stator spiral fixed in a housing, and a motor driven eccentric orbiting spiral.  …

Show More


Quick Links
Get in touch

0800 808 486

  help@ashair.co.nz

  Nationwide coverage, all regions



Keep up to date with news, promotions and more

Full URL


© 2026 Ash Air • Website design by Fuel