Why is a pneumatic grinder spinning too slowly?


Your tool is stalling, or is not working to its expected performance, and you find yourself asking ‘why is my angle grinder spinning too slowly?’, or ‘why has my pneumatic grinder stopped working?’, read on

In this scenario, it’s all too easy to blame the tool itself. However, there are two other fundamental factors that could be causing it to fail – the air line set-up and the maintenance regime – and these are often overlooked.

If your pneumatic angle grinder’s abrasive spin starts to slow down, or the motor stalls when you apply force then this is a tell-tale sign that the tool is not operating at full performance. It is vital to look out for these indicators, otherwise there will be a significant negative impact on productivity.

To try and prevent the tool from stalling, it is common practice to apply less force, but this means more time to complete the job, which results in reduced efficiency. If efficiency is affected, this will have major financial consequences and lead to a decrease in global production.

Let’s take a closer look at the two most common reasons affecting a pneumatic grinder’s performance.

1. Air line set-up & air line accessories

A pneumatic tool’s motor needs two things to work properly and at maximum speed:

  1. A dynamic air pressure of 90 psi / 6.3 bars at the tool inlet 
  2. Air flow as recommended by the tool manufacturer

Without the correct pressure and flow, the tool’s motor will not have enough energy to run the abrasive at full speed, resulting in a suboptimal efficiency (for rated speed, always check the abrasive manufacturer’s recommended speed).

How to get the right dynamic air pressure and air flow?

The choice of the right air line accessories (such as hose, couplings, FRL) is critical to ensure your tool’s performance. To demonstrate how performance can be affected, we have set up a CP3650 industrial pneumatic grinder with two different hose set-ups:

  1. One with the manufacturer recommended hose diameter (in this case: ½”) 
  2. One with a smaller hose diameter (in this case: 3/8”)

See the difference in performance for yourself – it’s astounding!

To ensure accessories fit the tool perfectly and deliver the best performance level, always refer to the tool manufacturer’s recommendations. There are four key values to consider when selecting your air line accessories:

  1. air line size, 
  2. air inlet type, 
  3. maximum air consumption at load, 
  4. recommended hose diameter/length.

To get tips on making sure you have the right air line set-up and good habits (such as air lubrication), download our guide Is your air tool installation right? This guide includes a valuable check list to help you do your own air line set-up evaluation.

2. Tools maintenance

Just as you would perform regular maintenance on your car, it is vital to carry out routine maintenance on your tools – to ensure they are kept in excellent working condition, and delivering a consistent high performance. After all, pneumatic tools are mechanical systems comprising wear parts that need regular inspection and changes (as required).

The parts that wear most frequently in pneumatic industrial grinders, and need regular maintenance are:

  1. Blades, with inspection recommended every 500 h
  2. Bevel gears (angle grinders and sanders only), with the maintenance interval specified as every 1000 to 2000h depending on the tools

Browse our tools and shop online

View 5 Products

Grinders & Sanders

For maximum material removal with minimum effort and high-quality finish, Chicago Pneumatic delivers robust, durable and lightweight easy-to-handle tools.

Surface applications from heavy material removal to fine finishing. Tools designed to bring better comfort and increase your productivity. The range provides random orbital sanders, rotary sanders, pistol sander & polishers, and belt sanders. Secure payment, Afterpay, nationwide delivery. Buy now, pay layer.

View 4 Products

Percussive Tools & Drills

Their combination of power, compactness and light weight gets the job done. Better operator comfort comes with a unique vibration dampening body.
The range provides industrial chipping hammers, weld flux chippers, needle scalers, long reach scalers and rust & weld scalers.

With drilling capacity from 6mm (1/4”) to 50mm (2”), various speeds and power, our drills are designed to handle both your tough and smooth operations. The range provides straight, angle and pistol drills. Secure payment, Afterpay, nationwide delivery. Buy now, pay layer.

View 13 Products

Specialty & Cutting

The range provides saws, high speed cutters, nibblers, shears, engraving pens, riveters, caulking guns, air files, and blow guns. Secure payment, Afterpay, nationwide delivery. Buy now, pay layer.

View 7 Products

Staplers & Brad Nailers

The perfect solution for all your nailing needs, from framing to decking and more. Our range of professional-grade brad nailers offer precision and durability to ensure you get the best results possible. As a professional tradesperson, our brad nailers are the ideal choice for any nailing task.

Explore our range of staple guns. Our brand of PIT TOOLS by Ash Air heavy-duty staplers we supply are trusted by tradespeople all over NZ.

Our Brad nailers and Staplers are suitable for a range of applications: Bedding and furniture, Cabinets and joinery, Fencing, Framing, Prefab housing, Wall lining, floor covering, cabinet making, trellis and boxes, interior decorative trim, cabinetry, cabinet backing, crafts and hobbies.

View 7 Products

Wrenches

The use of the latest technologies and materials, such as composite housing or steel housing for the toughest materials, makes CP Industrial impacts the best in each class. Our versatile line features different clutches such as rocking dog, 2 jaw, pin, single dog or twin dog clutches.

We offer a range of powerful pneumatic ratchet wrenches from ¼’ to ½” square drive for every task.
Due to their small size and light weight, pneumatic ratchets are an excellent choice for fastening in tight or cumbersome applications. Secure payment, Afterpay, nationwide delivery. Buy now, pay layer.

Do you have an idea for our #expertcorner? Let us know!

Useful links:

Book your Service here

Browse our Services here

Browse our Products here

Browse our News corner here

Browse our Sustainability focus here



Who we are and how Ash Air can help your business!

Ash Air has been around in New Zealand since 1979, and we’ve grown into a nationwide company with international support and a reputation for quality and reliability.We look after all things compressed air for your business!

  • Rotary Screw and Piston Air Compressors
  • Vacuum Pumps and Blowers
  • Nitrogen Generation
  • An extensive line of Air Treatment components
  • AIRnet Piping System and  Filtration
  • Mobile Compressors, Generators, and Light Towers

Ash Air's range of Chicago Pneumatic, ALUP, Pneumatech, and Atlas Copco products are used extensively around the world in industries ranging from oil and gas to food, automotive and farming, and we bring you these world-class compressors here in the land of the long white cloud.Our technicians are compressed air equipment experts and are dedicated to addressing customer needs. Supported with nationwide coverage, Ash Air offers one of the widest selections of compressed air, vacuum pump, and industrial gas equipment and parts available today in New Zealand.

Reliability and Efficiency

With Ash Air, you can count on reliability and high performance for even the most demanding applications. We focus our efforts on the following:

  • Increasing uptime
  • Reducing unexpected repairs
  • Reducing energy consumption and meeting our sustainability goals
  • Improving the cleanliness of compressed air


Talk to the team today:  CONTACT US CONTACT US

Read more from our #expertcorner


Air compressor leaks can be a substantial source of wasted energy in any system, sometimes wasting 20-30% of a compressor's production. Worst of all, a poorly maintained compressor can have a leak rate expected to equal 20% of total compressed air... …


Choosing the right compressor is essential to your long-term satisfaction and maybe, to the profitability of your business. Many times compressors are based on a single factor alone, such as horsepower or tank size, which is only part of the story. …


In oil injected screw compressors, there is a thin layer of oil found between the rotors to create a seal and maintain proper efficiency as the compression occurs. The unfortunate side effect of this solution is that oil may carry over to the point of use in your air system. This can be mitigated by having correct filtration in place to remove the oil contaminants in your air. Additionally, many individuals may decide to opt for a completely oil-free solution, with the use of a scroll compressor or water injected screw compressor. …


Most businesses concentrate on the air compressor and consider the piping as a secondary concern. The piping system can make or break your business. Faulty, inefficient piping can cause pressure loss and lost power. Keeping a close eye on the overall layout, installations and maintenance of your air piping system will help keep your business running at its’ optimal efficiency. …


Our #1 Focus is Customer Service! Whether you have questions about which compressor is right for you, or if you’re ready to improve your operations and start saving on expenses. Ash Air has been around for over 40 years because we offer reliable and hardworking air compressors, vacuum pumps, and services as well as expert advice and support. …


An oil analysis can prevent problems later down the road. It's often been referred to as the blood test for your compressor. Just like a blood test can tell you about your health and early alerts to impending problems, an analysis can do the same for your compressor. …




Did you know that pressure drops and leaks are the two largest areas of energy loss on your air compressors? It’s easy to understand why a leaking pipe or fitting creates energy loss. Pressure drops are not quite as noticeable, since you cannot hear ... …


Whenever anything doesn't work properly, it's frustrating and we get it. If this is your first time experiencing troubles with your dryer, you're probably unsure where to even start. Getting your dryer repaired and back up and working is critical to ... …


Screw compressors are helpful for an enormous range of applications such as air filling, packaging, tools, HVAC control, and more! One possible drawback is the amount of electricity they use; air compressors can be a huge drain on energy if used ​ine... …



Most air compressors require constant oil lubrication to prevent friction on the pistons or screws and other moving parts. To make sure your air compressor is running efficiently, it is important to check your oil level regularly and to know how much... …


Have you heard of the term "Total Air Solutions"? A total air solution means everything that goes with the compressor for your business’s air system. 90% of companies require more than just an air compressor.  …


When speaking of air compressors, compressed air treatment is a process that dehumidifies and cleans air before entering the compressor. Most commonly, this process involves air filters and an air dryer. …


Air compressors are used in many different applications and provide essential compressed air to many businesses and individuals with different air needs. No matter what your CFM, PSI and HP requirements are, the electronic controller on your air compressor is the motherboard for keeping your unit running as efficiently as possible. It is your eyes into your machine. …


Air compressors are helpful for an enormous range of applications such as air filling, packaging, tools, HVAC control, and more! One possible drawback is the amount of electricity they use; air compressors can be a huge drain on energy if used ​inefficiently​. If you are running them too long, allowing leaks to exist, or using the wrong type of compressor, you are wasting ​energy and money​. This article will go over some of the biggest power-wasters and how to
stop/prevent them! …



In the following guide, we want to try to answer some of the questions you may have been asking yourself in regards to screw air compressors. If you do not find the answer you are looking for, please get in touch with us. …


Compressed air is a key utility supporting the food packaging and food processing industries. It is used in machines that fill products such as cakes, pies, and liquid products, as well as during the packaging and transportation of snacks, vegetables, beer, soda and other items.. Compressed air must be moisture and contaminant-free to ensure the protection of the food products processed in each facility.  …


Minimizing the risk of accidents in the workplace is a top priority in industry, and it is especially important when working with pneumatic power tools. Ensuring that all safety precautions have been taken to protect the health and wellbeing of operators is vital. With this in mind, here are seven simple steps to reduce the risk of accidents and improve operator safety …


Regardless of the type of compressor you have, vibration issues can be troubling for any business. The root of the vibration can stem from multiple sources, some internally and others externally. Understanding the cause of the vibration and how to resolve them will be critical in keeping your compressor in proper working order. …


Air compressors are essential to your business, but they can also become a safety hazard when used improperly. Reading your owner’s manual and following all proper safety precautions before use is vital in keeping your compressor in great, working condition. …


Corrosion in the pipeline is due to insufficient condensation drainage that occurs during compression. The resulting condensate, together with the compressed air, flow further into the compressed air line network and has a negative effect on the pipes. Find out more about how you can prevent corrosion here. …


FRLs – Filters, Regulators and Lubricators – guarantee the efficiency and durability of pneumatic tools. Including an FRL in your air system is vital to running an efficient air line set-up and key to achieving a good return on investment. Read more here! …


Check out this blog and video included to help you know what you should be looking for when you're thinking about purchasing a Chicago Pneumatic Rotary Screw Compressor for your shop or application. If you want to learn about what a screw compressor actually is, check out this article   …


There are 3 simple steps to make sure your air line installation is providing the right pressure and that your accessories selection is correct, so you can ultimately work productively. It does not take long and it is something you can easily do yourself using our self-diagnostic checklist.  …


Okay, okay, we're a bit excited. With the recent launch of our air tools in our online shop. Here's a 101 for you about what air tools you might need in your air compressor tool kit. Air tools are prevalent in automotive industries, woodworking, construction, metalwork and more. Did you know that there's pretty much an air-powered version nearly any power tool on the market? We want to share with you our 'Must have Air Tools'. …


When you are thinking about an air compressor, you might be have the image of the super popular piston or reciprocating compressor in your mind. The compressor that you see in home workshops, automotive garages pumping up tyres and assisting in spray painting cars. …


As a follow on to our Why You Should Not Use PVC Piping for Your Compressed Air System blog, we share with you what piping you shouldbe using to get the most out of your compressed air system. Here at Ash Air we have the perfect solution if you're wanting to match your great compressor with a fast, easy and reliable piping solution that supports the operational excellence of your whole compressed air system.  …


An air compressor is a big purchase for any business. It is visibly important to properly maintain the air compressor and filter elements to protect that investment. Air intake filters are installed in an air compressor to remove any dust or debris the compress may suck in. Dust will cause wear to the compressor element, valves, filters, compressor oil and any moving parts. …


So you have a vacuum pump installed and you rely on it for your business operations and performance? Here are some reasons why you should consider overhauling your vacuum pump! s with all machinery and compressed air equipment, regular maintenance can help ensure optimised safer performance of your vacuum pump. Learn more about benefits of restoring, rebuilding and repairing your vacuum pump. …


Air compressors are used every day, by many industries around the world. They are often considered the heart of a business, in that most companies will rely on their performance and efficiency to run their operations, to get work done effectively and safely. In your day to day, you've probably seen air compressors in use - whether at a build site powering construction equipment or in a mechanics workshop inflating tyres. …


A scroll air compressor, or spiral compressor, compresses air by drawing it it, trapping it, reducing the volume and discharging it at the outlet port. The scroll compressor that you see today, such as SpiralAIR, have been the result of modernised advancements in manufacturing technology, even thought the concept of a scroll compressor has been around for over 100 years.The scroll compressor is oil-free orbiting, or positive displacement compressor. The compressor has a stator spiral fixed in a housing, and a motor driven eccentric orbiting spiral.  …

Show More

Quick Links
Get in touch

0800 808 486

  help@ashair.co.nz

  Nationwide coverage, all regions



Keep up to date with news, promotions and more

Full URL


© 2026 Ash Air • Website design by Fuel