How Do I Prevent My Air Compressor from Overheating?

If you notice that your compressor is getting hot and bothered, there may be heating issues affecting your air compressors performance. Did you know that an overheating compressor is top of the pops for being the most common cause of compressor failure.

What causes my air compressor to overheat?

Internal and external factors can affect your unit and typically the air will become hot before it cools and reaches it's endpoint. Thus, ventilation of your air compressor is crucial to ensuring it's running. In a reciprocating air compressor, the air temperature will drop anywhere from  10 degrees celsius to 24 degrees celsius across the roughly six inches of travel between the discharge port and discharge line. If the temperature at the discharge port exceeds 148 degrees celsius, the refrigerant oil and adjacent mechanisms will suffer.

For the health of the air compressor, the temperature at the discharge line should never exceed 107 degrees celsius. Anything hotter at the discharge line would put the discharge port dangerously above the 148 degrees celsius level. If the temperature exceeds 176 degrees celsius in the discharge port, the heat could lead to imminent system failure.

How do I know if my air compressor is overheating?

If your compressor is too hot and it's behaving questionably, the likehood is that it may be from heating issues.

1. Compressor Doesn’t Turn On

If the compressor fails to start up as normal, there is definitely something wrong with the machine that could likely stem from a heating issue. If the compressor requires longer durations between usage cycles, the internal components are probably taking longer to cool down between each cycle. Likewise, if the machine stalls during startup and ultimately takes longer to get into full operational mode, this is probably due to heat-degraded internal mechanisms.

2. Circuit Breaker Tripping

In an air compressor, the current flow is regulated by the circuit breaker, which stops the flow when necessary as a protective measure for the performance and quality of the machine. If the circuit breaker acts irregularly and trips at seemingly random moments, this is a tell-tale sign that bigger problems lurk inside the air compressor.

3. Accelerated Wear

When an air compressor starts to wear down at an accelerated pace, there is likely a more serious matter at hand. For example, if the machine exhibits performance issues just weeks after it was last serviced, something was probably not evaluated properly, be it a problem with the oil, the vents, the refrigerant or the condenser parts. If the air compressor is long before its time and yet already failing to handle basic demands, there could easily be an issue related to overheating.

4.  Oil-related Issues

An air compressor could emit noises or smells indicating oil erosion. If you can hear faint creaking noises from the machine that seem out of the ordinary, it could be a matter of insufficiently lubricated internal parts. A more clear-cut indicator of oil trouble is when an air compressor smells of burnt oil. Either way, the issue should be inspected immediately, as insufficient lubrication and poor oil quality can have a domino effect on the internal mechanisms of an air compressor.

What can I do to prevent my air compressor from overheating

If you need to cool your compressor down, and work to prevent it from overheating, here's what you can do: 

1. Focus on Improving Ventilation

The first step toward reversing a heating issue with an air compressor should focus on the internal and surrounding ventilation. Have each vent inspected to ensure that they are sufficient for the demands of the machine. If not, you will need to have the vents replaced. Ask your maintenance person the proper ventilation dimensions for the size of your system and the operations at hand.

Also, consider the external factors of the machine itself. If the machine is in an area that is either too hot or not sufficiently ventilated, arrange space for the machine in a more suitable area. Make sure that this new placement allows plenty of breathing room for each of the vents.

2. Monitor the Compressor’s Oil Level and Filters Regularly

As with any motorized machine or vehicle, it is crucial to ensure that the oil in an air compressor is healthy. Check the oil level on a regular basis to ensure that there is enough to handle the demands of your operations. Also, check the viscosity to make sure that the oil has not been rendered too thin or watery — this would be a sign of excess heat within the system. Moreover, check the filters during each oil inspection.

3. Monitor Ventilation and Ducting

Even after you have modified the layout of your workspace to better ventilate the air compressor and the surrounding temperatures, inspect the ventilation and ducting on a regular basis. If dirt or dust accumulate along the vents, clean them out accordingly. Make sure that the ducting flows properly and is not crimped or punctured at any point of the system.

Even if, in all practicality, you found no reason to reposition the machine, the vents could still have issues if they don’t receive due attention. An air compressor that cannot properly vent is liable to have heating issues, regardless of where the machine is placed.

4. Keep the Compressor Parts Up-To-Date

Because needs change, the air compressor that you purchase one year might not be sufficient in its initial state as the demands of your operations evolve. If your operations have demanded increased amounts of air power since the time that you first bought the machine, consider updating your air compressor with more optimal components.

When to call Ash Air Services?

When you realise that your compressor is likely overheating, contact us immediately. The longer you wait the higher the risk that your compressor may continue to run too hot and the problem will have costly and time consuming consequences.

Have a chat to us, your friendly New Zealand Air Compressor Specialists, and our service person will analyse the issue, tell you if it involves damage to more than one part, or if insufficient oil is involved. With inspections performed by us, you can ensure reliable performance for your compressed air system, year in, year out! It is worth considering replacement parts for your compressor unit(s), as your compressor could work with higher efficiency if you changed out older and worn parts. This may be the most beneficial option for your system, creating ease of suction, compressing air and send out cooler, cleaner air to your air tools.

Have a chat and see how we can help you today:


Do you have an idea for our #expertcorner? Let us know!

Useful links:

Compressor Services

Book Your Compressor Service


Who we are and how Ash Air can help your business!

Ash Air has been around in New Zealand since 1979, and we’ve grown into a nationwide company with international support and a reputation for quality and reliability.We look after all things compressed air for your business!

Ash Air's range of Chicago Pneumatic, Alup, Pneumatech, and Quincy compressors are used extensively around the world in industries ranging from oil and gas to food, automotive and farming, and we bring you these world class compressors here in the land of the long white cloud.Our technicians are compressed air equipment experts and are dedicated to addressing customer needs. Supported by a 13 locations nationwide, Ash Air offers one of the widest selections of compressed air equipment and parts available today in New Zealand.

Reliability and Efficiency

With Ash Air compressors, you can count on reliability and high performance for even the most demanding applications. We focus our efforts on the following:


Talk to the team today:  CONTACT US CONTACT US



Lighting tower reminds night, but also refers to diesel engine. In turn, night reminds us of silence, which is not exactly what we associate with an engine... With urban centers becoming increasingly dense and legislation increasingly strict about noise pollution in construction sites, keeping decibels to acceptable levels has been the great challenge of the main construction equipment manufacturers. …


In today’s world of increasing environmental awareness and the drive for sustainable practices, industries are actively seeking innovative solutions to reduce energy consumption and minimize their carbon footprint. If your business uses air compressors, focusing on energy recovery in air compressors is one area to pay attention too.  …


Did you know that 70% of the total cost of compressor installation consists of energy costs?

There are many reasons why saving energy is important for your business as it helps you in many ways to make your business more efficient as well as providing you with many different forms of value. Ash Air's range of Alup products can help you become more energy efficient to help reduce energy bills, reduce your costs and comply with all environmental legislation. …


Exactly what is compressed air? Where does it come from? What is it for? When we compress—or squeeze—air into a small space, we call it compressed air. When humans discovered the ability to compress air, civilisation made a huge leap forward. The reason? Compressed air opened the door to all kinds of new production methods.  …


Compressed air system leaks are indeed a big source of energy waste. Leakage in piping systems have been shown to exhibit leaks of up to 25 percent of the total energy costs. Addressing leaks is one of the first maintenance steps a facility can take to reduce energy costs. …


Think about efficiency for a minute. Every year with constant innovation, things are becoming even more efficient. Everything from electronics to industrial machinery are being developed to get more done faster while using less power. …


The air surrounding us is a mixture of fry air and water vapor. The amount of water in the air depends on the temperature and volume of the gas. The higher the air temperature, the higher the air's ability to absorb more moisture. Find out about compressed air humidity here. …


Investing in an on-site industrial gas generator is a great way to reduce your environmental footprint and your operating costs. Once you have taken this important step, there are some other things you can do to maximize your gas generation energy savings. Here are seven of them. …


For many businesses, preserving energy and becoming more sustainable have become top priorities. That not only saves them money but also makes them more competitive in the future, when demand for “green” products and services will only increase. Not just because governments mandate greater sustainability but also because customers expect it. …


While you relax and read this, do you see an electronic appliance around you? Wondering how could you relate to the current read? We got you! Compressed air is all around, in the electronic appliances you use right now. …


There are many contaminants that can threaten your compressed air system, but moisture is among the most prevalent. You may be thinking, but it’s just water, but water can have a devastating impact on your compressed air system, your production equipment, and your end product. The best way to prevent moisture from contaminating your compressed air is with a dryer. …


Compressed air can be one of the most expensive forms of energy for manufacturing plants, often using more energy than other equipment. One horsepower of compressed air requires eight horsepower of electricity. With many air compressors running at efficiencies as low as 10%, there’s often plenty of room for improvement. Fortunately, 50% of compressed air systems at small- to medium-sized industrial facilities have opportunities for low-cost energy conservation. …


As easy as it would make all of our lives, vacuum pumps are far from being “one size fits all”. Not only do you have the size to consider when choosing a vacuum pump, but more importantly type. I will briefly touch on some of the advantages and disadvantages associated with each vacuum technology we deal with. This should give you a better understanding of where to begin your search... …


AIRnet offers moisture-eliminating drop fittings called Quick Drops! Quick Drops make “drop-tees” obsolete, removing the need for extra parts and pipe, while saving time and money. …


Proper compressor installation and commissioning helps ensure trouble-free startup and long-term reliability. Thorough inspection and critical review during each phase of the installation process eliminates “built-in” deficiencies or problems which c... …


Price is an important consideration when choosing a tool for metalworking applications, but it alone should not be the deciding factor. Other things also contribute to the total cost of ownership, performance, and, ultimately, the overall productivit... …


Are you faced with the decision of whether to switch from purchasing bottled nitrogen or oxygen to on site gas generation? In that case, the decision is easy. You should! Lower costs, the right purity, less transportation emissions, improved safety, no logistics headaches. In all of these areas, on site gas generation is the superior solution. And making the switch is easy. All you need is a gas generator and a supply of compressed air. …


Did you know that one of the largest costs for industrial manufacturers is compressed air? That’s right – anywhere from 12% to 40% of a facility’s total energy costs come from its compressed air installation. This means that finding innovative ways (no matter how small) to increase compressed air efficiency can amount to big savings over the long run! Items like leak elimination, air audits, reduced pressure bands, and reducing unloaded running hours are some of the most popular ways to decrease energy usage – but there are many other actions that you can take. Read on to discover additional ways to reduce your costs and make sure your compressor system is running as efficiently as possible! …


A properly sized and designed piping system is a necessary component of any distribution compressed air system. Without this key component in place, the delivery of air from the compressor to the specific points of use will be inefficient and costly, both in the short term as well as in the long term. Let’s look more closely at how to size your compressed air piping system to ensure minimal pressure loss while maintaining maximum efficiency. …


Potential for growth of micro-organisms in a compressed air system is tied to the moisture level (dew point) of the compressed air. In simple terms, if there is moisture in your compressed air, microorganisms such as mold and bacteria have the environment they need to grow and thrive. While it’s true that as air is compressed, much of the moisture present in the intake air will condense, enough moisture remains to allow micro-organisms to proliferate. …


Your compressor installation is a workhorse that requires regular service and maintenance to help it achieve maximum efficiency and longevity. This is where compressor monitoring and data gathering technologies come in, as these provide meaningful information on your system that can be visualized, tracked over extended time periods, and used to make insightful decisions regarding compressor performance.  …


A variable speed compressor is not for every application. VSD rotary screw compressors need to be ran in a location that is in need of 24/7 compressed air and has a changing demand on the amount of air needed. If your compressed air needs are constan... …


Compressed air purification equipment must have a very low pressure drop, long service life and be strong enough to withstand the most strenuous operating conditions. Protection from oil slugs or compressor air/oil separator failure is essential. …


Intelligent Connectivity System (ICONS) is the eyes into your compressed air system. Ditch the logbooks, the regular visits to the compressor room and dealing with surprises with your compressor. • Most maintenance organizations operate between 10% to 40% efficiency • Most spend more than 50% of time on emergency work • Reactive maintenance costs 3-5 times more than preventive maintenance. …


Compressed air is used in many different industries. From refrigerator manufacturers to toy makers, companies around the world depend on compressed air to produce products. It's so important that many consider it a utility as significant as electricity, water or natural gas. …


Compressed air is always contaminated. Contaminants include, • Liquid oil - oil aerosols - oil vapor, Dirt - microorganisms - pipescale, Trace gases: carbon monoxide, sulfur dioxide, nitrous oxide. Learn more about why you need to filter compressed air...  …


As part of a concerted effort worldwide to reduce energy consumption, CO2 emissions and the impact of industrial operations on the environment, regulatory authorities in many countries have introduced legislation to encourage the manufacture and use ... …


Air is always contaminated with solid particles such as dust, sand, soot, salt crystals and water as it leaves the compressor. An effective compressed air treatment system lowers the dew point of the air and takes out the elements that may harm equipment downstream of the compressor and dryer …


Dewpoint spikes immediately after desiccant switchover (line C) indicate that the desiccant was not sufficiently cooled before being brought on-line. Hot desiccant will not adsorb moisture well until it cools down, after which the dewpoint should dro... …


Don’t be alarmed if you find oil in your air compressor tank. Actually, all rotary screw compressors pass trace amounts of oil in the compressed air. The question is how much is the normal amount of oil in my compressor tank? …


As you know, compressed air filters protect your machine from dirt, dust, oil and water. These contaminants are extremely common in the areas you would find a compressed air system and will wear down your machine if not properly filtered out. …

Show More
Quick Links
Get in touch

0800 808 486

  help@ashair.co.nz

  Nationwide coverage, all regions



Keep up to date with news, promotions and more

Full URL


© 2026 Ash Air • Website design by Fuel